Initial checkin

logseq/bak/pages/G5C/2025-05-01T18_48_55.970Z.Desktop.md

@@ -0,0 +1,99 @@
+G5C – Resistors, capacitors, and inductors in series and parallel; transformers
+
+- [[G5C01]] (C)
+What causes a voltage to appear across the secondary winding of a transformer when an AC voltage source is connected across its primary winding?
+	- A. Capacitive coupling
+	- B. Displacement current coupling
+	- C. Mutual inductance
+	- D. Mutual capacitance
+--
+- [[G5C02]] (A)
+What is the output voltage if an input signal is applied to the secondary winding of a 4:1 voltage step-down transformer instead of the primary winding?
+	- A. The input voltage is multiplied by 4
+	- B. The input voltage is divided by 4
+	- C. Additional resistance must be added in series with the primary to prevent overload
+	- D. Additional resistance must be added in parallel with the secondary to prevent overload
+--
+- [[G5C03]] (A)
+What is the total resistance of a 10-, a 20-, and a 50-ohm resistor connected in parallel?
+	- A. 5.9 ohms
+	- B. 0.17 ohms
+	- C. 17 ohms
+	- D. 80 ohms
+--
+- [[G5C04]] (D)
+What is the approximate total resistance of a 100- and a 200-ohm resistor in parallel?
+	- A. 300 ohms
+	- B. 150 ohms
+	- C. 75 ohms
+	- D. 67 ohms
+--
+- [[G5C05]] (B)
+Why is the primary winding wire of a voltage step-up transformer usually a larger size than that of the secondary winding?
+	- A. To improve the coupling between the primary and secondary
+	- B. To accommodate the higher current of the primary
+	- C. To prevent parasitic oscillations due to resistive losses in the primary
+	- D. To ensure that the volume of the primary winding is equal to the volume of the secondary winding
+--
+- [[G5C06]] (A)
+What is the voltage output of a transformer with a 500-turn primary and a 1500-turn secondary when 120 VAC is applied to the primary?
+	- A. 360 volts
+	- B. 120 volts
+	- C. 40 volts
+	- D. 25.5 volts 
+--
+- [[G5C07]] (A)
+What transformer turns ratio matches an antenna’s 600-ohm feed point impedance to a 50-ohm coaxial cable?
+	- A. 3.5 to 1
+	- B. 12 to 1
+	- C. 24 to 1
+	- D. 144 to 1
+--
+- [[G5C08]] (D)
+What is the equivalent capacitance of two 5.0-nanofarad capacitors and one 750-picofarad capacitor connected in parallel?
+	- A. 576.9 nanofarads
+	- B. 1,733 picofarads
+	- C. 3,583 picofarads
+	- D. 10.750 nanofarads
+--
+- [[G5C09]] (C)
+What is the capacitance of three 100-microfarad capacitors connected in series?
+	- A. 0.33 microfarads
+	- B. 3.0 microfarads
+	- C. 33.3 microfarads
+	- D. 300 microfarads
+--
+- [[G5C10]] (C)
+What is the inductance of three 10-millihenry inductors connected in parallel?
+	- A. 0.30 henries
+	- B. 3.3 henries
+	- C. 3.3 millihenries
+	- D. 30 millihenries
+--
+- [[G5C11]] (C)
+What is the inductance of a circuit with a 20-millihenry inductor connected in series with a 50-millihenry inductor?
+	- A. 7 millihenries
+	- B. 14.3 millihenries
+	- C. 70 millihenries
+	- D. 1,000 millihenries
+--
+- [[G5C12]] (B)
+What is the capacitance of a 20-microfarad capacitor connected in series with a 50-microfarad capacitor?
+	- A. 0.07 microfarads
+	- B. 14.3 microfarads
+	- C. 70 microfarads
+	- D. 1,000 microfarads
+--
+- [[G5C13]] (C)
+Which of the following components should be added to a capacitor to increase the capacitance?
+	- A. An inductor in series
+	- B. An inductor in parallel
+	- C. A capacitor in parallel
+	- D. A capacitor in series
+--
+- [[G5C14]] (D)
+Which of the following components should be added to an inductor to increase the inductance?
+	- A. A capacitor in series
+	- B. A capacitor in parallel
+	- C. An inductor in parallel
+	- D. An inductor in series