Initial checkin

logseq/bak/pages/G4D/2025-05-01T18_48_55.968Z.Desktop.md

@@ -0,0 +1,78 @@
+G4D – Speech processors; S meters; sideband operation near band edges
+
+- [[G4D01]] (A)
+What is the purpose of a speech processor in a transceiver?
+	- A. Increase the apparent loudness of transmitted voice signals
+	- B. Increase transmitter bass response for more natural-sounding SSB signals
+	- C. Prevent distortion of voice signals
+	- D. Decrease high-frequency voice output to prevent out-of-band operation
+--
+- [[G4D02]] (B)
+How does a speech processor affect a single sideband phone signal?
+	- A. It increases peak power
+	- B. It increases average power
+	- C. It reduces harmonic distortion
+	- D. It reduces intermodulation distortion
+--
+- [[G4D03]] (D)
+What is the effect of an incorrectly adjusted speech processor?
+	- A. Distorted speech
+	- B. Excess intermodulation products
+	- C. Excessive background noise
+	- D. All these choices are correct
+--
+- [[G4D04]] (C)
+What does an S meter measure?
+	- A. Carrier suppression
+	- B. Impedance
+	- C. Received signal strength
+	- D. Transmitter power output
+--
+- [[G4D05]] (D)
+How does a signal that reads 20 dB over S9 compare to one that reads S9 on a receiver, assuming a properly calibrated S meter?
+	- A. It is 10 times less powerful
+	- B. It is 20 times less powerful
+	- C. It is 20 times more powerful
+	- D. It is 100 times more powerful
+--
+- [[G4D06]] (A)
+How much change in signal strength is typically represented by one S unit?
+	- A. 6 dB
+	- B. 12 dB
+	- C. 15 dB
+	- D. 18 dB
+--
+- [[G4D07]] (C)
+How much must the power output of a transmitter be raised to change the S meter reading on a distant receiver from S8 to S9?
+	- A. Approximately 1.5 times
+	- B. Approximately 2 times
+	- C. Approximately 4 times
+	- D. Approximately 8 times
+--
+- [[G4D08]] (C)
+What frequency range is occupied by a 3 kHz LSB signal when the displayed carrier frequency is set to 7.178 MHz?
+	- A. 7.178 MHz to 7.181 MHz
+	- B. 7.178 MHz to 7.184 MHz
+	- C. 7.175 MHz to 7.178 MHz
+	- D. 7.1765 MHz to 7.1795 MHz
+--
+- [[G4D09]] (B)
+What frequency range is occupied by a 3 kHz USB signal with the displayed carrier frequency set to 14.347 MHz?
+	- A. 14.347 MHz to 14.647 MHz
+	- B. 14.347 MHz to 14.350 MHz
+	- C. 14.344 MHz to 14.347 MHz
+	- D. 14.3455 MHz to 14.3485 MHz
+--
+- [[G4D10]] (A)
+How close to the lower edge of a band’s phone segment should your displayed carrier frequency be when using 3 kHz wide LSB?
+	- A. At least 3 kHz above the edge of the segment
+	- B. At least 3 kHz below the edge of the segment
+	- C. At least 1 kHz below the edge of the segment
+	- D. At least 1 kHz above the edge of the segment
+--
+- [[G4D11]] (B)
+How close to the upper edge of a band’s phone segment should your displayed carrier frequency be when using 3 kHz wide USB?
+	- A. At least 3 kHz above the edge of the band
+	- B. At least 3 kHz below the edge of the band
+	- C. At least 1 kHz above the edge of the segment
+	- D. At least 1 kHz below the edge of the segment