100 lines
3.4 KiB
Markdown
100 lines
3.4 KiB
Markdown
G7C – Transceiver design; filters; oscillators; digital signal processing (DSP)
|
||
|
||
- [[G7C01]] (B)
|
||
What circuit is used to select one of the sidebands from a balanced modulator?
|
||
- A. Carrier oscillator
|
||
- B. Filter
|
||
- C. IF amplifier
|
||
- D. RF amplifier
|
||
--
|
||
- [[G7C02]] (D)
|
||
What output is produced by a balanced modulator?
|
||
- A. Frequency modulated RF
|
||
- B. Audio with equalized frequency response
|
||
- C. Audio extracted from the modulation signal
|
||
- D. Double-sideband modulated RF
|
||
--
|
||
- [[G7C03]] (B)
|
||
What is one reason to use an impedance matching transformer at a transmitter output?
|
||
- A. To minimize transmitter power output
|
||
- B. To present the desired impedance to the transmitter and feed line
|
||
- C. To reduce power supply ripple
|
||
- D. To minimize radiation resistance
|
||
--
|
||
- [[G7C04]] (D)
|
||
How is a product detector used?
|
||
- A. Used in test gear to detect spurious mixing products
|
||
- B. Used in transmitter to perform frequency multiplication
|
||
- C. Used in an FM receiver to filter out unwanted sidebands
|
||
- D. Used in a single sideband receiver to extract the modulated signal
|
||
--
|
||
- [[G7C05]] (D)
|
||
Which of the following is characteristic of a direct digital synthesizer (DDS)?
|
||
- A. Extremely narrow tuning range
|
||
- B. Relatively high-power output
|
||
- C. Pure sine wave output
|
||
- D. Variable output frequency with the stability of a crystal oscillator
|
||
--
|
||
- [[G7C06]] (A)
|
||
Which of the following is an advantage of a digital signal processing (DSP) filter compared to an analog filter?
|
||
- A. A wide range of filter bandwidths and shapes can be created
|
||
- B. Fewer digital components are required
|
||
- C. Mixing products are greatly reduced
|
||
- D. The DSP filter is much more effective at VHF frequencies
|
||
--
|
||
- [[G7C07]] (A)
|
||
What term specifies a filter’s attenuation inside its passband?
|
||
- A. Insertion loss
|
||
- B. Return loss
|
||
- C. Q
|
||
- D. Ultimate rejection
|
||
--
|
||
- [[G7C08]] (D)
|
||
Which parameter affects receiver sensitivity?
|
||
- A. Input amplifier gain
|
||
- B. Demodulator stage bandwidth
|
||
- C. Input amplifier noise figure
|
||
- D. All these choices are correct
|
||
--
|
||
- [[G7C09]] (B)
|
||
What is the phase difference between the I and Q RF signals that software-defined radio (SDR) equipment uses for modulation and demodulation?
|
||
- A. Zero
|
||
- B. 90 degrees
|
||
- C. 180 degrees
|
||
- D. 45 degrees
|
||
--
|
||
- [[G7C10]] (B)
|
||
What is an advantage of using I-Q modulation with software-defined radios (SDRs)?
|
||
- A. The need for high resolution analog-to-digital converters is eliminated
|
||
- B. All types of modulation can be created with appropriate processing
|
||
- C. Minimum detectible signal level is reduced
|
||
- D. Automatic conversion of the signal from digital to analog
|
||
--
|
||
- [[G7C11]] (D)
|
||
Which of these functions is performed by software in a software-defined radio (SDR)?
|
||
- A. Filtering
|
||
- B. Detection
|
||
- C. Modulation
|
||
- D. All these choices are correct
|
||
--
|
||
- [[G7C12]] (C)
|
||
What is the frequency above which a low-pass filter’s output power is less than half the input power?
|
||
- A. Notch frequency
|
||
- B. Neper frequency
|
||
- C. Cutoff frequency
|
||
- D. Rolloff frequency
|
||
--
|
||
- [[G7C13]] (D)
|
||
What term specifies a filter’s maximum ability to reject signals outside its passband?
|
||
- A. Notch depth
|
||
- B. Rolloff
|
||
- C. Insertion loss
|
||
- D. Ultimate rejection
|
||
--
|
||
- [[G7C14]] (A)
|
||
The bandwidth of a band-pass filter is measured between what two frequencies?
|
||
- A. Upper and lower half-power
|
||
- B. Cutoff and rolloff
|
||
- C. Pole and zero
|
||
- D. Image and harmonic
|