69 lines
3.6 KiB
Markdown
69 lines
3.6 KiB
Markdown
E4A Test equipment: analog and digital instruments; spectrum analyzers; antenna analyzers; oscilloscopes; RF measurements
|
||
|
||
- [[E4A01]] (A)
|
||
Which of the following limits the highest frequency signal that can be accurately displayed on a digital oscilloscope? #card
|
||
- [[A.]] Sampling rate of the analog-to-digital converter
|
||
- [[B.]] Analog-to-digital converter reference frequency
|
||
- [[C.]] Q of the circuit
|
||
- [[D.]] All these choices are correct
|
||
- [[E4A02]] (B)
|
||
Which of the following parameters does a spectrum analyzer display on the vertical and horizontal axes? #card
|
||
- [[A.]] Signal amplitude and time
|
||
- [[B.]] Signal amplitude and frequency
|
||
- [[C.]] SWR and frequency
|
||
- [[D.]] SWR and time
|
||
- [[E4A03]] (B)
|
||
Which of the following test instruments is used to display spurious signals and/or intermodulation distortion products generated by an SSB transmitter? #card
|
||
- [[A.]] Differential resolver
|
||
- [[B.]] Spectrum analyzer
|
||
- [[C.]] Logic analyzer
|
||
- [[D.]] Network analyzer
|
||
- [[E4A04]] (A)
|
||
How is compensation of an oscilloscope probe performed? #card
|
||
- [[A.]] A square wave is displayed, and the probe is adjusted until the horizontal portions of the displayed wave are as nearly flat as possible
|
||
- [[B.]] A high frequency sine wave is displayed, and the probe is adjusted for maximum amplitude
|
||
- [[C.]] A frequency standard is displayed, and the probe is adjusted until the deflection time is accurate
|
||
- [[D.]] A DC voltage standard is displayed, and the probe is adjusted until the displayed voltage is accurate
|
||
- [[E4A05]] (D)
|
||
What is the purpose of using a prescaler with a frequency counter? #card
|
||
- [[A.]] Amplify low-level signals for more accurate counting
|
||
- [[B.]] Multiply a higher frequency signal so a low-frequency counter can display the operating frequency
|
||
- [[C.]] Prevent oscillation in a low-frequency counter circuit
|
||
- [[D.]] Reduce the signal frequency to within the counter's operating range
|
||
- [[E4A06]] (A)
|
||
What is the effect of aliasing on a digital oscilloscope when displaying a waveform? #card
|
||
- [[A.]] A false, jittery low-frequency version of the waveform is displayed
|
||
- [[B.]] The waveform DC offset will be inaccurate
|
||
- [[C.]] Calibration of the vertical scale is no longer valid
|
||
- [[D.]] Excessive blanking occurs, which prevents display of the waveform
|
||
- [[E4A07]] (B)
|
||
Which of the following is an advantage of using an antenna analyzer compared to an SWR bridge? #card
|
||
- [[A.]] Antenna analyzers automatically tune your antenna for resonance
|
||
- [[B.]] Antenna analyzers compute SWR and impedance automatically
|
||
- [[C.]] Antenna analyzers display a time-varying representation of the modulation envelope
|
||
- [[D.]] All these choices are correct
|
||
- [[E4A08]] (D)
|
||
Which of the following is used to measure SWR? #card
|
||
- [[A.]] Directional wattmeter
|
||
- [[B.]] Vector network analyzer
|
||
- [[C.]] Antenna analyzer
|
||
- [[D.]] All these choices are correct
|
||
- [[E4A09]] (A)
|
||
Which of the following is good practice when using an oscilloscope probe? #card
|
||
- [[A.]] Minimize the length of the probe's ground connection
|
||
- [[B.]] Never use a high-impedance probe to measure a low-impedance circuit
|
||
- [[C.]] Never use a DC-coupled probe to measure an AC circuit
|
||
- [[D.]] All these choices are correct
|
||
- [[E4A10]] (D)
|
||
Which trigger mode is most effective when using an oscilloscope to measure a linear power supply’s output ripple? #card
|
||
- [[A.]] Single-shot
|
||
- [[B.]] Edge
|
||
- [[C.]] Level
|
||
- [[D.]] Line
|
||
- [[E4A11]] (D)
|
||
Which of the following can be measured with an antenna analyzer? #card
|
||
- [[A.]] Velocity factor
|
||
- [[B.]] Cable length
|
||
- [[C.]] Resonant frequency of a tuned circuit
|
||
- [[D.]] All these choices are correct
|