Initial checkin

logseq/bak/pages/E9E/2025-05-01T20_36_51.635Z.Desktop.md

@@ -0,0 +1,74 @@
+E9E Impedance matching: matching antennas to feed lines; phasing lines; power dividers
+
+- [[E9E01]] (B)
+Which matching system for Yagi antennas requires the driven element to be insulated from the boom? #card
+	- [[A.]] Gamma 
+	- [[B.]] Beta or hairpin
+	- [[C.]] Shunt-fed
+	- [[D.]] T-match
+--
+- [[E9E02]] (A)
+What antenna matching system matches coaxial cable to an antenna by connecting the shield to the center of the antenna and the conductor a fraction of a wavelength to one side? #card
+	- [[A.]] Gamma match
+	- [[B.]] Delta match
+	- [[C.]] T-match
+	- [[D.]] Stub match
+--
+- [[E9E03]] (D)
+What matching system uses a short length of transmission line connected in parallel with the feed line at or near the feed point? #card
+	- [[A.]] Gamma match
+	- [[B.]] Delta match
+	- [[C.]] T-match
+	- [[D.]] Stub match
+--
+- [[E9E04]] (B)
+What is the purpose of the series capacitor in a gamma match? #card
+	- [[A.]] To provide DC isolation between the feed line and the antenna
+	- [[B.]] To cancel unwanted inductive reactance
+	- [[C.]] To provide a rejection notch that prevents the radiation of harmonics
+	- [[D.]] To transform the antenna impedance to a higher value
+--
+- [[E9E05]] (A)
+What Yagi driven element feed point impedance is required to use a beta or hairpin matching system? #card
+	- [[A.]] Capacitive (driven element electrically shorter than 1/2 wavelength)
+	- [[B.]] Inductive (driven element electrically longer than 1/2 wavelength)
+	- [[C.]] Purely resistive
+	- [[D.]] Purely reactive
+--
+- [[E9E06]] (C)
+Which of these transmission line impedances would be suitable for constructing a quarter-wave Q-section for matching a 100-ohm feed point impedance to a 50-ohm transmission line? #card
+	- [[A.]] 50 ohms
+	- [[B.]] 62 ohms
+	- [[C.]] 75 ohms
+	- [[D.]] 90 ohms
+--
+- [[E9E07]] (B)
+What parameter describes the interaction of a load and transmission line? #card
+	- [[A.]] Characteristic impedance
+	- [[B.]] Reflection coefficient
+	- [[C.]] Velocity factor
+	- [[D.]] Dielectric constant
+--
+- [[E9E08]] (C)
+What is a use for a Wilkinson divider? #card
+	- [[A.]] To divide the operating frequency of a transmitter signal so it can be used on a lower frequency band
+	- [[B.]] To feed high-impedance antennas from a low-impedance source
+	- [[C.]] To divide power equally between two 50-ohm loads while maintaining 50-ohm input impedance
+	- [[D.]] To divide the frequency of the input to a counter to increase its frequency range
+--
+- [[E9E09]] (C)
+Which of the following is used to shunt feed a grounded tower at its base? #card
+	- [[A.]] Double-bazooka match
+	- [[B.]] Beta or hairpin match
+	- [[C.]] Gamma match
+	- [[D.]] All these choices are correct
+--
+- [[E9E10]]  Question Deleted (section not renumbered)
+~~
+
+- [[E9E11]] (A)
+What is the purpose of using multiple driven elements connected through phasing lines? #card
+	- [[A.]] To control the antenna’s radiation pattern
+	- [[B.]] To prevent harmonic radiation from the transmitter
+	- [[C.]] To allow single-band antennas to operate on other bands
+	- [[D.]] To create a low-angle radiation pattern